SBC MT 01 Spezifikationen PDF herunterladen (Seite 73)

Fig. 18

MT SBC 01

Functions that can be associated with a pushbutton

Standard function: Door lock release

This function enables you to programme the selected pushbutton to

perform the door lock release function on the external unit. The

function does not require the programming of any Parameter.

The Door lock release command can be used to release the door

lock at the bottom of the stairs (Function D) using Art. 1256.

For settings and further information, see page 52.

Standard function: Switchboard

This function enables you to programme the selected pushbutton to

perform the Call porter switchboard function for Art. 1998A.

The function does not require the programming of any Parameter.

The ‘call porter switchboard’ function can be used to activate

actuator Art. 1256 (Function B). For settings and further

information, see page 52.

Standard function: Switch-on

This meaning of this function depends on how the monitor is set.

If the monitor is Main the pushbutton programmed with this

function performs automatic switch-on.

If the monitor is Secondary the pushbutton programmed with this

function activates a video request.

Automatic switch-on of the monitor takes place when you press

and immediately release the programmed pushbutton and is only

possible when the system is in standby. If two external units are

installed, pressing the automatic monitor switch-on pushbutton

twice will show you the image first from one and then from the

other external unit. Automatic switch-on can be disabled (see

variant H on page 129).

The video request function enables you to switch on a monitor

following a call from an external unit for the user. The monitor

switches on automatically when speech mode is activated or when

the pushbutton programmed for this function is pressed and

released (see variant H on page 129).

Standard function: Actuator

This function enables you to programme the selected pushbutton to

perform the uncoded Actuator function.

With the pushbutton thus set, it is possible to activate all the

actuator relay modules Art. 1256 set to function E.

The function does not require the programming of any Parameter.

See page 52 for the settings of Art.1256 and other details.

Standard function: Coded Actuator

This function enables you to programme the selected pushbutton to

perform the Coded actuator function.

With the pushbutton thus set, it is possible to activate

the relay only on actuator relay module Art. 1256 set to function F,

provided it has been given with the same code as the one

programmed with Art. 1251/A for the pushbutton on the internal

extension.

The function requires programming of the Parameter field of the

code of actuator Art. 1256 that you want to control.

The code of actuator Art. 1256 must be written in the Parameter

field (see example in figure 19), which can be read on the DIP

switch of the device according to the DIP switch programming table

on page 79. For settings of Art. 1256 and further information, see

page 52.

Figure 4 shows the factory settings of the pushbuttons. Using 1251/A,

however, you can customise each pushbutton of the monitor to

perform one of the following functions:

• Door lock release

• Call to porter switchboard

• Automatic switch-on (Switch-on)

• Generic

• Coded actuator

• Doctor

• Video request (Switch-on)

• Privacy (for Art. 4784, 4784I and 2418W only)

• Intercom call (Art. 4897, 5714CI, 4784I, 2418W and 2618 only)

• Intercom group call (Art. 4897, 5714CI, 4784I, 2418W and 2618

only)

It is also possible to:

- Read the configuration of all pushbuttons.

- Save the configuration of the pushbuttons read.

- Cancel the single pushbutton and therefore make it

unprogrammed.

- Retrieve a user configuration of the pushbuttons to be

programmed.

- Retrieve a factory-set configuration of pushbuttons for

programming.

Only for Art. 5714CI, 4784I and 2618:

- Read the intercom code.

- Programme the intercom code.

- Delete the intercom code.

- Read the output of Art. 4897.

Note that interphones Art. 2618 and 2418W, if used in a non-

intercommunicating system, i.e. without interface Art. 4897, must

have no intercommunicating code set.

To delete any intercommunicating code that may have been set,

use the submenu Canc. Intercom. Art. 2418W and Art. 2618 are

factory-set with no intercommunicating code and are therefore

ready for use in non-intercommunicating systems (not connected to

Art. 4897).

Custom settings on Art. 4897

On Art. 4897 intercommunicating interface for Simplebus systems,

you can read or delete the intercommunicating network configuration

on the interface by selecting, respectively:

Read Cfg.

Reset Cfg.

at the time of connection.

Audio ON/OFF

(NOT PROGRAMMABLE)

Automatic

switch-on

Privacy

Door lock

release

Switchboard Actuator

1 2 ... 68 69 70 71 72 73 74 75 76 77 78 ... 131 132

Kommentare zu diesen Handbüchern

Keine Kommentare

SBC MT 01 Spezifikationen Seite 73

Kommentare zu diesen Handbüchern